Documentation Center |
Bilevel waveform pulse width
W = pulsewidth(X)
W = pulsewidth(X,FS)
W = pulsewidth(X,T)
[W,INITCROSS]
= pulsewidth(...)
[W,INITCROSS,FINALCROSS]
= pulsewidth(...)
[W,INITCROSS,FINALCROSS,MIDLEV]
= pulsewidth(...)
W = pulsewidth(...,Name,Value)
pulsewidth(...)
W = pulsewidth(X) returns a vector, W, containing the time differences between the mid-reference level instants of the initial and final transitions of each positive-polarity pulse in the bilevel waveform, X. To determine the transitions, pulsewidth estimates the low- and high-state levels of X by a histogram method. pulsewidth identifies all regions that cross the upper-state boundary of the low state and the lower-state boundary of the high state. The low-state and high-state boundaries are expressed as the state level plus or minus a multiple of the difference between the state levels. See State-Level Tolerances. Because pulsewidth uses interpolation to determine the mid-reference level instants, W may contain values that do not correspond to sampling instants of the bilevel waveform, X.
W = pulsewidth(X,FS) specifies the sample rate, FS, in hertz as a positive scalar. The first sample in the waveform corresponds to t=0. Because pulsewidth uses interpolation to determine the mid-reference level instants, W may contain values that do not correspond to sampling instants of the bilevel waveform, X.
W = pulsewidth(X,T) specifies the sample instants, T, as a vector with the same number of elements as X. Because pulsewidth uses interpolation to determine the mid-reference level instants, W may contain values that do not correspond to sampling instants of the bilevel waveform, X.
[W,INITCROSS] = pulsewidth(...) returns a column vector, INITCROSS, whose elements correspond to the mid-reference level instants of the initial transition of each pulse.
[W,INITCROSS,FINALCROSS] = pulsewidth(...) returns a column vector, FINALCROSS, whose elements correspond to the mid-reference level instants of the final transition of each pulse.
[W,INITCROSS,FINALCROSS,MIDLEV] = pulsewidth(...) returns the waveform value, MIDLEV, which corresponds to the mid-reference level.
W = pulsewidth(...,Name,Value) returns the pulse widths with additional options specified by one or more Name,Value pair arguments.
pulsewidth(...) plots the signal and darkens the regions of each pulse where pulse width is computed. It marks the location of the mid crossings, and their associated reference level. The state levels and their associated lower and upper boundaries (adjustable by the Name,Value pair with name 'Tolerance') are also plotted.
X |
Bilevel waveform. X is a real-valued row or column vector. |
FS |
Sample rate in hertz. |
T |
Vector of sample instants. The length of T must equal the length of the bilevel waveform, X. |
'MidPercentReferenceLevel' |
Mid-reference level as percentage of the waveform amplitude. See Mid-Reference Level. Default: 50 |
'Polarity' |
Pulse polarity. Specify the polarity as 'positive' or 'negative'. If you specify 'positive', pulsewidth looks for pulses with positive-going (positive polarity) initial transitions. If you specify 'negative', pulsewidth looks for pulses with negative-going (negative polarity) initial transitions. See Pulse Polarity. Default: 'positive' |
'StateLevels' |
Low- and high-state levels. StateLevels is a 1-by-2 real-valued vector. The first element is the low-state level. The second element is the high-state level. If you do not specify low- and high-state levels, pulsewidth estimates the state levels from the input waveform using the histogram method. |
'Tolerance' |
Tolerance levels (lower and upper state boundaries) expressed as a percentage. See State-Level Tolerances. Default: 2 |
W |
Pulse widths in seconds. The pulse width is the time difference between the initial and final transitions of a pulse. The times of the initial and final transitions are referred to as transition occurence instants in [1]. |
INITCROSS |
Mid-reference level instants of the initial transition |
FINALCROSS |
Mid-reference level instants of the final transition |
MIDLEV |
Waveform value corresponding to the mid-reference level |
The mid-reference level in a bilevel waveform with low-state level, S_1, and high- state level, S_2, is
Let y_{50%} denote the mid-reference level.
Let t_{50%-} and t_{50%+} denote the two consecutive sampling instants corresponding to the waveform values nearest in value to y_{50%}.
Let y_{50%-} and y_{50%+} denote the waveform values at t_{50%-} and t_{50%+}.
The mid-reference level instant is
If the pulse has a positive-going initial transition, the pulse has positive polarity. The following figure shows a positive-polarity pulse.
Equivalently, a positive-polarity (positive-going) pulse has a terminating state more positive than the originating state.
If the pulse has a negative-going initial transition, the pulse has negative polarity. The following figure shows a negative-polarity pulse.
Equivalently, a negative-polarity (negative-going) pulse has a originating state more positive than the terminating state.
Each state level can have an associated lower- and upper-state boundary. These state boundaries are defined as the state level plus or minus a scalar multiple of the difference between the high state and low state. To provide a useful tolerance region, the scalar is typically a small number such as 2/100 or 3/100. In general, the α% tolerance region for the low state is defined as
where S_{1} is the low-state level and S_{2} is the high-state level. Replace the first term in the equation with S_{2} to obtain the α% tolerance region for the high state.
The following figure illustrates lower and upper 2% state boundaries (tolerance regions) for a positive-polarity bilevel waveform. The red dashed lines indicate the estimated state levels.
[1] IEEE^{®} Standard on Transitions, Pulses, and Related Waveforms, IEEE Standard 181, 2003.